Search Our Site

Case study

Oil-Water Separator Engineering for a Guyana Gold Mine

An above-ground separator design for wash-bay and maintenance-pit requirements.

Above-ground oil-water separator vessel showing its long side, low flange and support feet

A Guyana-based gold mining venture needed to manage oily water from a wash bay and a maintenance pit. The wash-bay baseline was approximately 60 gallons per minute (GPM), with allowance for gravity-fed solids. Separately, the maintenance requirement called for 200 GPM from a 150 m³ pit, with a target of draining it in approximately three hours.

Ecologix developed an above-ground oil-water separator design and an auxiliary pump package for the stated requirements. The available record documents design and approval; it does not establish installation or measured field performance.

Application Snapshot

ApplicationWash-bay and maintenance-pit oily water at a gold mining venture in Guyana
Wash-bay baselineApproximately 60 GPM, with allowance for gravity-fed solids
Maintenance pit150 m³, with a 200 GPM requirement and approximately three-hour drain-time target
LayoutAbove-ground separator requested for site flexibility
Wash waterHigh-pressure, ambient-temperature water with biodegradable degreasers, as reported by the client

The three-hour drain time was a client target, not a measured result or guarantee. At 200 US GPM, continuously pumping 150 m³ would nominally take about 3 hours and 18 minutes, before allowing for operating conditions.

Requirements and Design Evolution

High-pressure washing and the use of degreasers made the condition of the oil relevant to separation. Gravity separation depends on oil droplets being able to rise; emulsified oil can remain suspended and may require additional treatment. The reported use of biodegradable degreasers does not by itself establish that the oil would remain non-emulsified.

In October 2025, the early discussion included an underground HQB-1048 option with a 1,000-gallon tank and 100 GPM capacity. After the formal request for proposal in November, Ecologix provided above- and below-ground layouts in December and sought clarification of the operating flows. The client supplied data sheets and clarified the wash-bay and maintenance-pit requirements in January 2026.

By April 2026, Ecologix had been named a shortlisted finalist and issued a revised quotation reflecting the updated scope. The executive summary describes the above-ground design as approved; the available chronology does not independently confirm a final award or completed installation.

Specified Above-Ground Separator

The specified AG-5CS-HP above-ground oil-water separator has a design flow range of 1-200 GPM. Its parallel corrugated plate coalescer provides surfaces where non-emulsified oil droplets can combine and rise under calm, laminar-flow conditions.

The source specifies 100% removal of non-emulsified oil droplets at least 30 µm in diameter under laminar flow. This is a design specification, not a demonstrated field result or a claim about emulsified oil.

SpecificationSpecified value
Tank construction¼-inch ASTM A36 carbon steel
Internal coatingTnemec 61, 10-12 mils minimum dry film thickness
External coatingPolyamide epoxy, 6 mils minimum dry film thickness
Total separator volume1,942 gallons
Effluent tank volume323 gallons
Sludge hopper capacity75 gallons
Above-ground separator vessel with a low flanged connection on its end face
Above-ground separator vessel viewed from the end, showing the low flanged connection and support feet.

Specified Pump Duties

The quoted pump duties are listed separately from the overall wash-bay and maintenance-pit requirements. The source identifies a 60 GPM wash-bay baseline and, separately, a 200 GPM pump named for wash-bay circulation.

Quoted dutySpecified equipment
Wash-bay circulation3-inch bolted Wilden air-operated double-diaphragm (AODD) pump, 200 GPM over a 25 m pipe run, aluminum wetted body and Buna elastomers
Truck-shop circulation1½-inch bolted Wilden AODD pump, 60 GPM over a 75 m pipe run
Wash-bay sludge2 HP lobe pump with pressure transducer and liquid-level float kits
Separator vessel showing a high flanged connection, lower hopper and support frame
Separator vessel viewed from the opposite end, showing the high flange, hopper and support frame.

Project Status and Engineering Takeaways

The documented milestone is an approved design and a revised quotation following selection as a shortlisted finalist. Manufacture, shipment, installation, commissioning, compliance and field performance are not independently established by the supplied record.

This application illustrates why oil-water separator selection needs to account for instantaneous flow, solids, oil condition and the intended layout alongside total water volume.

Planning treatment for oily wash water?

Share your flow rates, solids loading, oil condition and site requirements with the Ecologix team.

Request Assistance